free web maker

Copyright © 2018 - All Rights Reserved Lanka Aluminium Industries PLC 

Specification of Aluminium Extrusion

We confirm that the Aluminium Extrusions manufactured by us for architectural
purposes confirm to the following specifications.
Primary quality billets confirming to American Standard AA6063, Homogenized, and
LME registered with Fe content less than 0.2% is used to manufacture all our products.
All mill finish materials are hardened to yield a temper of T6 – T8.
Other standard physical and mechanical properties are as follows:-
Density - 2.7 g /cc
Hardness, Vickers - 76
Tensile Strength, Ultimate - 185 Mpa
Tensile Strength, Yield - 145 Mpa
Elongation at break - 12%
Modules of Elasticity - 69 Gpa
Shear Strength - 115 Mpa
Electrical Receptivity - 0.0000031 ohm – cm
Melting Point - 616 ºC
Two-step Anodizing / Electro Colour process is used. Anodic coating thickness to be
agreed by customer Maximum coat thickness available is 20 – 25 microns. Coating
thickness is measured on significant surfaces as per British Standard BS1615 of 1987,
BS6469 of 1984. Coating thickness ranges from (10 – 12), (15 – 20), (21 -25).
Powder coated materials are manufactured using architectural grade pure polyester
powder with high quality “Henkel” pre-treatment. Standard average powder coating
thickness is 60-80 microns on the significant surfaces as per BS1615. Powder used to
coat the products meet GSB, Qualicoat and and British Standards for weathering,
adhesion, impact, etc.
Every batch is tested prior to dispatch and carries a Company Warranty on all
manufacturing defects.

APPLICATIONS

Alloy (6063 / IS ) :Al, MgO, 7 Si

Composition :

Element (wt. %)

Silicon (Si)

Iron (Fe)

Copper( Cu)

Manganese( Mn)

Magnesium (Mg)

Chromium (Cr)

Zinc (Zn)

Titanium (Ti)

Others: Each


Applications


















Products Forms



Al 0.7 Mg 0.4 Si

Minimum                           Maximum

0.35                                    0.45

0.14                                     0.20

                                            0.02

                                            0.02

0.45                                   0.55

                                            0.02

                                            0.02

0.003                                 0.03

                                            0.02


Architectural sections for windows, doors,

curtain walls. Interior fittings, frame

systems, lighting, ladders, railings, etc..

Heat sink sections, electronic modules,

electro motor housing. Flexible assembly

systems, special machinery elements.

Truck and trailer flooring, pneumatic

installation, railway, inside applications.

Irrigation pipes, furniture, office

equipment. Radiator and other heat

exchanger applications.

Very good corrosion resistance. Very good

weld ability. Medium strength heat

treatable alloy slightly lower than 6005A.

Medium fatigue strength. Good cold

formability especially in temper T4. Suit

able for very complex cross sections.

Standard decorative anodizing quality.

Sheet, Bar, Rod, Wire, Tube, Profile

section, Shape, Slugs Impacts.

MECHANICAL PROPERTIES

Mobirise

RP02N

RP02

RMN


RM


RG

A5N

A5

A50N

A50

HBN

HB

HV

    Min Proof stress 0.2%

    Proof Stress 0.2%

    Min ultimate tensile strength

    Ultimate tensile strength

    Shear stress

    Min elongation A5

    Elongation

    Min elongation A50

    Elongation A50

    Min Hardness, Brinell

    Hardness, Brinell

    Hardness, Vickers

      Mpa

      Mpa

      Mpa


      Mpa


      Mpa

      %

      %

      %

      %

      HBN

      HB

      Hv

        CORROSION AND ANODIZING PROPERTIES

        Mobirise

        Key to Parameters:                                               
        COA:

        COIA :

        COMA:

        SCOA:

        EXCA:

        ICOA :

        PCA :

        ANBA:

        ANCA:

        ANHA:

        ANPA:



          Corrosion Index, General
          Industrial atm corr Index
          Marine atm corr Index

          Rural atm corr Index

          Exfoliation corrosion Index
          Inter crystalline corrosion Index
          Pitting corrosion Index

          Bright anodizing Index

          Colour anodizing Index

          Hard anodizing Index

          Protective anodizing Index



            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

            Scale 2 – 7

              Key to Values

              5 Good

              %

              5 -6 Good to Very Good                         

              %

              6 Very Good

              %

              7 Excellent

              %